Sample Price : 55Us$
100 Pieces = 46 Us$
Product Overview
Thank you
for purchasing,This device is a waterproof IPX6, innovative miniature
size personal remote positioning device with built-in U-blox GPS and GSM/GPRS
technology. It’s for monitoring and protecting people and property. It can be
used in all walks of life from traveling lone workers and mobile nursing staff
to children and the elderly, Dementia etc.
SIM
card Installation
The SIM card is not included in the
package. A Micro SIM card is
available from the user's local operator.
-
Unscrew the back cover and remove
the cover.
-
Insert SIM card and make sure it’s
activated with credits
-
Put the cover back and tighten the
screws.
Note: Before installing the SIM card, check
if the SIM card has PIN code or not, if yes, please use a cell-phone to unlock
the card's PIN code.
Device Charging
For the first time use, please
fully charge the battery for around 2~3 hours
Using the USB charger or using docking station to charge
-
Place the device on the docking station.
-
Connect the Micro USB side of the cable to
the docking station port and connect the other end of the cable to the
designated AC power source (USB/AC adaptor).
-
When charging, the RED LED (on docking station) will be blinking (solid).
After fully charging, the RED LED will solid.
Switching
the device on and off
-
To turn on the device: press the side power button for 1 second, all
the LEDs will flash rapidly. Device can be also turned on automatically by
charging via USB or put it into the docking station.
※ To get an initial location,
use outdoors or near a window so the device may fix onto the satellites.
-
To turn off the device: press and hold the side button and SOS
button together for 1 second until the LEDs off.
Activating an SOS Alarm
Press and hold the SOS button for 3 seconds until the device
vibrates, and then green light will start to flash rapidly to confirm the
request. After that, an SOS Alarm "Help me!" will be sent to all
authorized phone numbers and to the platform. It will also the dial the 3
authorized numbers in sequence. If the tracker fails to connect to the first
number, it will call the second one. In case the second number fails to be
connected as well, the system will connect to the third number. if device fails
to call all 3 numbers, it will start to dial the numbers again after 5 minutes.
This will continue until one of the phones answer the call.
To
end the call, press the SOS button.
Making a Phone Call
To make a call,
press and hold the side button for 3 seconds and you
will hear a beep. The green light will flash rapidly to confirm
the request, and
then it will dial the second number. To end the call, press the SOS
button.
Configuration and Operation by SMS
1. To Set the Authorized Number
※ It is not mandatory for all three of the
authorized numbers to be set, however a minimum of one must always be set.
① Command: A1 or A1,phone number
Note: With no
spaces in the text, case-insensitive.
Example: A1 or a1,123456789
※ Using your mobile phone, send A1 to the phone number
of the device, it will reply: ·Set mobile
number 1 OK!
※ To delete this number, you can
send A0 to
the tracker.
②Command: B1 or B1,phone number
Example: B1 or b1,123456789
The device will
reply: ·Set mobile number 2 OK!
※ To delete this number, you can
send B0
③Command: C1 or C1,phone number
Example: C1 or c1,123456789
The device will reply: ·Set mobile number 3 OK!
※ To delete this number, you can send C0
2. Modify
the Time zone
Command: TZ+ +00/-00
Note: the time must amounts be in 2 digits and at
maximum 23 hours in value. “+” in the “time zone” portion of the text indicates
east. The symbol “-“ in the “time zone” indicates west.
Example: tz+02, the system will add 2 hours
based on the UTC time.
tz-02, the system will minus 2 hours
based on the UTC time.
※ UTC time has been set as default time.
3. User defined name in SMS content
Command: name1,
user name
Example: name1,Emma,
the tracker will reply “Add name ok!”
※ To delete name, you can send name0
4. Location request
4.1 Reply with
coordinates and web link
Command: loc
The device will reply “GPS Info! Time: xxxxx; Lat: xxxx; Lon: xxxx; Spd: xxxxx, Altitude:xxxx Bt: xxx
maps.google.com/maps?q=loc:22.647379,114.030998
※Put coordinates to Google earth or Google maps.
Click on search button, then you will find the position fixed.
※Click on the link then the location can be
shown directly on Google Map on your mobile phone.
4.2 Reply with Address
Command: add
Notes: This function needs GPRS function support.
The device will reply “Add: Donghuan 1st road, Bao’an,
UK;
5. Low battery alarm
When the unit’s battery is less than 15%, it will send an SMS alarm “BAT:
LOW!” to all authorized numbers. If battery is less than 15%, the blue light will flash rapidly to
warn the user to charge the device as soon as possible.
Command: Low1
To turn
off this function, please send Low0 the device.
6. PIN LOCK
Command: 123456lock
After send
this command, then it will require a password in front of all commands (except
reboot and RESET!). For example 123456LOC, 123456A1 etc. (default password is
123456)
Remove
password protection, just simply send 123456unlock
7, Change password:
Command: Old password + H + new password
Example: 123456H666666
The password now is changed to
666666
※ The pre-set password won’t be erased by changing a new sim card.
※ Be sure keep the new password in mind, otherwise you have to ask
your distributor to restore the original setting in case of losing the new
password.
※ Make sure the new password is in
6 digits, or else the tracker can not recognize the password.
8. GEO-Fence Alarm
Command: G+X, Y, Z, xxxM/KM
Example: G1,1,1,100M
Notes: No spaces in between.
X=No.
of Geo fence (1~3), user can set 3 Geo fences
Y=0
means to turn off the function
Y=1 means to turn on the function
Z=1
means to set alarm when the tracker enters the preset area
Z=0
means to set alarm when the tracker breaches the district
xxx is the preset
distance to the tracker’s original place, must be
3 digitals. M means meters, KM means
kilometers
The device will send the message
to the authorized numbers as “Geo fence alarm!+GPS info” when it enter the area you set.
(User must set this function when the blue light is
flashing rapidly.)
To turn off this function, please send G1,0 or G2,0 or G3,0
9. Over-Speed alert
Command: speed1,+ Speed
Notes: The speed must be in km/h in 2 or 3 digitals. (01~255km/h)
Example: speed1,100
Suppose the over-speed alert that we want to
set is 100km/h, when the device exceeds 100km/h, it will send the message “Over-speed! +GPS Info” to all registered phone
numbers.
To turn off
this function, please send speed0 to the device.
10. Movement Alert
Command: M1, xxxM/KM
Notes: xxx must be 3
digitals. M means meters, KM means kilometers
The
tracker must be stationary when setting this function
Example: m1,100m
When the tracker moves
beyond 100 meters, it will send an SMS alarm to
all
registered phone numbers.
To turn off this function, please
send M0 to the device.
(The settings must be at least 50 meters)
11. Listen-in (Voice
wiretapping)
Command: L1
A1, B1, C1 can make a silence call
to the tracker, the track answers the call automatically and allows the caller
to hear what is happening around the tracker.
There is no voice indication that the call is in progress.
To turn
off this function, please send L0 to the device.
12. Motion alarm
Command: V1, xx S/M/H
Note: No spaces in between, S means seconds, M means
minutes, H means hours, xx means the time you set
and must be two digitals.
Example: V1,05M
Device will detect motion every 5 minutes and
will send an SMS warning alarm to all registered phone numbers.
To turn off this function, please send V0
13. Turn off 3 LEDs
Command: LED1
The device will reply “LED off” and later LEDs will stop flashing, but the device is
actually on.
To turn on LEDs, please send LED0
14. AGPS
Command: AGPS1, latitude,
longitude
Example: AGPS1,22.647606,114.022583
Assisted GPS (abbreviated generally as A-GPS and less commonly as aGPS) is a system that is often able to significantly improve the startup performance or time-to-first-fix (TTFF) and improve the GPS location to be more precise, of a GPS satellite-based positioning system.
To turn off this function, please send AGPS0
15. Fall detection
A simple fall may cause a
devastating consequence. The authorized numbers will be alerted without the
user pushing SOS button when the fall sensor is activated.
Command: FL1
The device must sense both
impact and angle.
To turn off this function, please send FL0
16. Check settings
Command: status
The device will reply E.g. A+8613812345678 B13912345678 C13712345678; Speed: 0,100km/h; GEO:0,0,0; VB:1,10S; MV:1,100; LED:0; TZ:2.0; LI: 1; PS:1; DS:0,3M; FL:1; Bat: 95%; SMS:0;LOCK:0
To
recognize the meaning of “0”& “1”
The number “0” implies that the function is turned off; whilst “1” indicates that the function is
turned on.
Device 5 working modes
1. Live Tracking Mode (1)
Command: PS0
In
this mode, Both GSM and GPS are on all the time, Battery can last 18~24
hours.
2. Smart Power Saving Mode (2)
(default mode)
Command: PS1
In
this mode, the gsm chip is working and receives calls, SMS and transmits
location. The GPS chip is activated by motion, incoming calls and SMS. The GPS
chip is off when there is no movement or no phone usage. Battery life is
not wasted when the device isn't moving.
Under normal use, battery can last 3 ~ 7
days.
3. Deep Sleeping Mode (3)
Command: DS1 or
DS1,xxM/H
Both GSM and GPS chip will be
off to save power, the device is unable to receive calls or SMS.
It can be only activated by
movement. Once movement is detected, it will run for the set time and sleep
again if no movement is detected.
Battery can last 40 days if no
movement at all.
To turn off this function, send DS0
4, Press button working mode (4)
Command: Mode4
In this working mode, device can always
receive SMS, calls. But GPS chip only wakes up and updates location to the
tracking platform if user press button.
Without press button, GPS chip will always
sleep.
5, Time interval working mode (5)
Command: Mode5,xxS/M/H
Example: Mode5,10M
Device will update location to
the tracking platform every 10 minutes.
In this working mode, device can always
receive SMS, calls. And it updates location to the tracking platform according
to the time you set.
Real time tracking on www.smart-tracking.com
Our web based
tracking system incorporates the TCP/IP protocol and allows users to monitor it
in real time over the internet or sends an e-mail to the predefined e-mail
address.
How to
connect device to the platform for real time tracking via GPRS
1. Get IMEI number
Command: version
The device will reply” IMEI: 123456789123456;
GSM CSQ:xxxx; Soft:V07.20.10.1345”
2. Go to the website www.smart-tracking.com and login with your account.
3. On the left side, click "Manage→Add Tracker”
Note:
- Hardware Version: Select EV07
- Type tracker name and IMEI number,
make sure IMEI numbers are correct.
4. GPRS Setting
In order to use the GPRS function, the user
needs to setup the APN by sending SMS command.
--What is APN?
Access point name (APN) is the name used to identify a general packet radio service
(GPRS) bearer service in the GSM mobile network. The APN defines the type of
service that is provided in the packet data connection.
※ Make sure that the SIM card in the tracker supports the GPRS
function.
※ The APN
can be acquired from your local GSM operators.
Command: S1, APN, user name, password
Notes: Some access point name without user name and
password, so please leave it blank.
Example: S1,internet
“internet” is the APN from the SIM card
provider; therefore the user must set their particular APN for their own
country which the unit resides.
After sending the command, the device will
reply “Set APN OK! GPRS connecting”
After send S1,APN, wait for a while then you will see
device is online.
Set GPRS Time interval by SMS (this can be also set from platform)
Command: TIxxS/M/H
The meaning of “xx”, The setting must be in 2 digitals
and maximum 99 in value, which means 01~99.
xxS is the time interval in second with
range(30~99)
xxM is the time interval in minute with
range(01~99)
xxH is the time interval in hour with
range(01~99)
Example: TI01M
The device will
reply “Set updating time interval OK!” and then device will update the time by
every 1 minute on the website.
Disable GPRS
Command: S0
The device will reply “GPRS OFF”.
Reconnect GPRS
Reconnect the website via GPRS for real time
tracking, please send S2
Check APN & IP, Port
Command: G1
The device will reply “APN: internet; Name: xxx; Password: xxxx; Port: 5050; IP:www.smart-tracking.com”
Change IP and Port
Command: IP1,IP/domain name,port
Example:
IP1,103.21.211.11,5050 or IP1,www.smart-tracking.com,5050
Disable SMS alert
Command: SMS0
It only
send alarms via GPRS to the platform and without text message to the authorized
numbers.
Enable
SMS and GPRS alarms, just simply send SMS1 (default setting)
Reboot device
Command: reboot
The device will
restart itself without changing any settings.
Initialization:
Command: RESET!
Note: This is to make all settings back to
the factory default.
Built-in Memory
The device built in 8MB flash memory inside. It will store the GPS
information when do not have GSM network coverage (i.e.,
very low population density areas, some mountainous terrain, underground areas
etc). The device will transmit GPS locations to
the WEB server automatically once the GSM network is recovered.
Delete stored tracking history data
Command: flush
The device will stop sending the stored
tracking history data to tracking platform.
Cautions:
Please
comply with the instructions to extend the unit life:
1.
Don’t use
& store the unit in dusty places.
2.
Don’t put
the unit in overheated or over cooled places.
3.
Clear the
unit with a piece of dry cloth. Don’t clean in chemicals, detergent.
4.
Don’t
disassemble or refit the unit.
5.
Using
other batteries will cause unwanted situation
Hardware Specification:
Content
|
Specs.
|
Mainframe Dimension
|
61mm*43mm*16mm
|
Net Weight
|
15g
|
GSM Frequencies
|
900/180/850/1900Mhz
|
GPS chip
|
U-blox 7 (Support AGPS)
|
GPS sensitivity
|
Cold start: -148dBm Hot start: -162dBm
|
GPS accuracy
|
<2.5m
|
Time to First Fix
|
Cold start 32s, Warm
start 11s,
Hot start 1s
|
Charging
Voltage
|
5V DC
|
Battery
|
Chargeable 3.7V 800mAh
|
Standby Current
|
≤2mAh
|
Storage Temperature
|
-40°C to +85°C
|
Operation Temperature
|
-20°C to +80°C
|
Humidity
|
5%-95% non-condensing
|
0 comments:
Post a Comment